Veneered Plywood
- 350+ architectural veneers & inlays in exact quantity
- Supplied as matched sets
- Max size 5300x1300mm or 3050x2440mm
(subject to core availability) - 1.2mm to 60mm thick (composites up to 100mm)
- Supplied raw or coated with various coatings such as clear lacquer or oil
- Click to see standard veneered plywoods as 2440x1220mm sheets
Overview
Premier Grade architectural veneered plywood can be made to order using any one of our range of 350+ veneers & inlays - or any other veneer specified, e.g. dyed veneers. These highly decorative panels are available in standard sizes (e.g. 2440x1220mm), although they are most often ordered in specific sizes as a bespoke bookmatched set.
Typical installations are high-quality bespoke kitchens, bedrooms, bathrooms, shopfitting & joinery.
We also offer Commercial Grades in pallet quantities of the more standard veneers where price is the main consideration.
In detail
Winwood Products is a supplier of the following veneered plywood panels:
Veneered Plywood
- Quantity:
- Premier GradeSupplied in standard size or as fully matched sets of architectural veneered panels to specific design, order quantity & layout
- Merchant, Commercial Joinery & Superior gradesSupplied in full pallets (typically 25 sheets per item)
- Standard size:
- 2440/2745/3050x1220mm
- Max size:
- Premier GradeAny bespoke size up to max. 5300x1300mm / 3050x2440mm
(subject to availability of core) - Superior GradeAny size up to max. 3670x1870 / 1870x3670mm
(subject to availability of core)
- Premier GradeAny bespoke size up to max. 5300x1300mm / 3050x2440mm
- Thickness:
- Premier Grade1.5mm to 100mm - dependent upon plywood type
(composites up to 100mm) - Merchant, Commercial Joinery & Superior grades6mm to 30mm
- Premier Grade1.5mm to 100mm - dependent upon plywood type
- Panel types:
- Gluing:
- Premier GradeFace veneers bonded using moisture-resistant glue as standard - other glues used to special order, e.g. exterior glue, formaldehyde-free, etc.
- Merchant, Commercial Joinery & Superior gradesFace veneers bonded with interior glue
- Cut sizes:
- Premier GradeCore material cut to size before veneers are applied to arrangement or design specified
- Merchant, Commercial Joinery & Superior gradesFinished boards optimized & cut from standard panel size
- Edging:
- Premier GradeConcealed solid lumber lipping or veneer edging applied before calibration of faces & over-veneering
- Merchant, Commercial Joinery & Superior gradesEdging can be retro-fitted (not recommended wherever possible)
- Finishing:
- All items can be supplied raw or coated with various coatings such as clear lacquer or oil
Veneered Thin Flexible Plywood
- Quantity:
- Premier Grade onlySupplied in standard size or as fully matched sets of architectural veneered panels to specific design, order quantity & layout
- Standard size:
- Produced to specific bespoke size
- Max size:
- Any bespoke size up to max. 3050x1220mm
- Thickness:
- 1.2mm (2-ply) & 1.8mm (3-ply) - supplied unsanded
- Gluing:
- Moisture-resistant glue used as standard
- Edging:
- Not possible
- Finishing:
- Flexible items need to be finished after installation
Information
Tolerances (general)
- Thickness:
- Varies according to the core material used - plus nominal veneer thickness
- NB: Premier Grade panels are calibrated before veneering to ensure best adhesion
- Veneer thickness:
- Most veneers are approx. 0.6mm before sanding - adds approx 0.5mm per side if supplied presanded
- Thicker veneers will typically finish approx. 0.3mm thinner than the original veneer thickness, e.g. 2.5mm veneers will add approx. 2.2mm per side if presanded
- Panel size:
- Standard size panels:Length/width: up to 1m @ ±1mm, up to 2m @ ±2mm , 2m & above @ ±3mm
- Cut size/bespoke panels:Length/width: typically ±1mm unless CNC machined (typically ±0.2mm)
- Non-standard tolerances by arrangement